Systema Professional Training Weapon M16-A2-MAX Evolution (M150 Cylinder)

Three years have passed since the last large-scale improvement, and there have been remarkable changes in the Environment for close-range battle training.

Therefore, Systema has received a lot of requests for further improvement in the function of P.T.W. as equipment.
After verifying from various angles, we release the final improved version.

This time, three main themes are:

(1) Improvement of basic performance
(2) Enhancement in durable performance
(3) Securing the long-distance range

Now, let me introduce the last evolution form of P. T. W.

7511 Type Motor
For the 2012 model, the start torque as well as the durability has been further polished in the 7511 type motor. Considered to be the core of the motor, the Rotor has been completely redesigned.

The new improvements are listed below.

・The die used for the Core Piece has been reconstructed. The Core Piece is turned 120 degrees every time it is punched out; creating a rotary lamination, by doing so it compresses the Core Piece rotary balance to the maximum due to the deviation of the board thickness.
・New Comutator
Systema changed the thickness of the board on the terminal area, and secured the rigidity of the winding coil tension, at the same time, we greatly improved the durability.
・Systema changed the grade of heat resistance used in the winding coil.
・Larger Bearing

Systema replaced the Bearing on the End Bell side to one size larger. By changing out the Bearing we noticed an improvement to the precision in processing as well as an improvement to the rotary balance.
・Systema also changed the heat resistance of the magnet to the highest grade.

With these improvements, our new 7511 type motor is able to maintain torque properties identical to another motor produced by us (the Magnum motor); considering the size of our new motor compared to other AEG motors it is unbelievable .

Please confirm for yourself to the power produced. The ability in our newest evolved P.T.W. 7511 type motor

Stainless Steel cylinder case.
The Cylinder Case for out T.W. has been conventionally manufactured from pushing out one piece aluminum, however with a minor change we switched to using SUS304 for our main Cylinder Case. Systema received reports of damage to the Cylinder from people dropping the Cylinder Units or BBs spilling out from the magazine thus damaging the Cylinder which then would not be able to be reinserted to the upper receiver (thus rendering it unusable); as a countermeasure Systema improved the rigidity of the Cylinder Case. Using our prior experience in producing our Bore Up Cylinders, we are able to recreate the extremely high precision in the inner and outer dimensions in the production of our Stainless Steel Cylinder, and using aluminum only to necessary parts. An Aluminum rail is inserted onto the Stainless Steel cylinder, using a key to stop the rail, we adopted a technique called the facture method to finish the process at the same time.

Increasing distance without increasing power
Most who experience holding an airgun have sought after the solution to this query. One solution may come from the current mainstream HOP structure. The T.W. is no exception and we also adopted this structure. However, contrary to conventional standards we were relentless to focus on range rather than simply increasing power to achieve that; we looked towards improving the trajectory via manipulation of the parabola of power which we determined it to be the HOP structure. We believe that this is the most suitable choice given that most training situations engagement of the enemy is less than 20 meters. However, the power necessary to get an ideal trajectory cannot evade the risk of point-blank shots. In addition, recent training standards require a shooting range more than 40 meters at the same time an even higher level of precision and accuracy; Systema polished up two parts that we will explain below, and the answer which Systema came up with is our model.

Accuracy Inner Barrel
The path to the T.W. Inner Barrel At the time of release the dimension for our T.W. inner barrel was 6.1mm in diameter; the concept to which was to allow the compressed air to wrap the BB as it pushed through the inner barrel. When compressed air and balance of the BB weight were negated, this method showed high performance; however, with the use of heavy BBs or in the case of using poor precision BBs the Inner Barrel is not capable of correcting trajectory therefore extreme flyers (BBs flying in erratic directions) occur. Therefore we went in the opposite direction and created an extremely narrow Inner Barrel where the inside diameter is now 6.04mm.

This revision resulted in the improvement of trajectory by increasing more power, and although this improvement achieved a constant result, due to the narrow inner diameter; as the BBs pass through the Inner Barrel, the frequency in which the BB scrapes the inner wall of the barrel increased thus resulted in performance that Systema were not satisfied with. Because the gap between the BB and the barrel decreases as the inside diameter of the barrel is more narrow, efficiency rises, as the power of the compressed air pushing on the BB contributes to power. However, the BB which accelerated in the inner barrel will be pushed out of the barrel more abruptly due to the decrease in the amount of air that surrounds the BB. Moreover, Systema believes that; because compressed air will continue to push the BB after it exits the inner barrel the trajectory may become more unstable.

These deductions are not common, however this way of thinking has been around for quite some time; through various trial manufacturing Systema decided on a specific designed inner barrel tip which produced a consistent result.

New Hop Adjuster
As stated in the previous article, we used the HOP structure "to mainly correct trajectory" and did not use it for the purpose of extending the flight distance. However, despite it being close quarter battle training, it is very unnatural that a round does not reach the target when there is clearly visual confirmation. Systema created the M90 cylinder unit that can provide a safety margin where one can pull the trigger without hesitation at any time. The goal of achieving an average 50 meters to target in conjunction with our recommended Cylinder Unit; through much of our trial and error resulted in the introduction to Systemas new roller packing Hop adjuster. This medical grade silicon rubber material is used in our roller packing; while soft it is durable and has an outer diameter size of 40% larger than conventional versions which increases distance. In addition, with regards to range to target trajectory; along with the combination of high grade BBs, distance that what was once given up on with conventional technology is now achievable

5. MAGPUL Parts
For the 2012 model, Systema incorporated the MAGPUL Company’s back-up rear site as well as the trigger guard in our Challenge Kit. With this Systema discovered that a large reduction in the overall weight. Furthermore, in terms of the site; because of the flip up type, it facilitates the addition of one’s own favorite optical sighting device.

8 Years has passes since Systema first yearned to achieve our goal of “Creating the best and strongest AEG in history”. In that time, Systema has made great improvements to bring the Training Weapon to where it is presently, however in regards to functional improvements Systema believes that this will be the last. Systema believes that this product has been fully concluded. Through the effort of everyone were able to realize the official adoption of our product to the United States Armed Forces, which in the beginning Systema thought was impossible. In regards to quality and workmanship Systema can assert that our newest T.W. has left no stone unturned. Systema would be happy if everyone would test it for themselves. Systema thanks you for your continued support. Systema continues to strive for the best every day. By all means please pick up and try out our ultimate T.W. Systema and Imperial believe that we will be able to convey the quality and performance of Systema products.